The Bcan Rebounder Meta Springs closes by twisting the spring collar counterclockwise until it releases from the frame

The Bcan Rebounder Meta Springs is a small fitness trampoline with springs that connect the jumping mat to the base frame. To close it, you rotate the metal collar at the top of each spring shaft counterclockwise by hand until the spring detaches. Once all springs are released, the mat folds down flat against the base, and the legs fold inward for storage.

This design is different from some other rebounders that use a quick-release button or lever. The Bcan model requires manual twisting, which takes a few minutes but gives you a secure hold while the rebounder is in use.

Key Takeaways

  • Turn the spring collar counterclockwise by hand to release each spring from the frame.
  • You must release all springs before the mat will fold down completely.
  • After springs are loose, fold the mat down and then fold the legs inward toward the center.
  • Store the closed rebounder in a dry place, as moisture can rust the springs over time.

Step-by-step closing process

Start by standing next to the rebounder so you can reach the springs easily. Locate the metal collar at the top of the first spring shaft — this is the part that screws into the frame. Grip the collar firmly with your hand and turn it counterclockwise. You should feel resistance at first, but it will loosen as you turn.

Continue turning until the spring comes free from the shaft. The spring will still be attached to the mat on the other end, so it will not fall. Repeat this process for every spring around the rebounder. Most Bcan models have six to eight springs, depending on the size.

Once all springs are loose, gently pull the mat down toward the base frame. The mat should fold flat against the frame without resistance. If you feel tension, check that you have released every spring — even one tight spring will prevent the mat from folding completely.

Folding the legs after the mat is closed

After the mat is flat, locate the leg hinges where each leg connects to the frame. These are usually at the bottom corners or sides of the base. Push or pull each leg inward toward the center of the rebounder. The legs should fold in smoothly if the hinges are not damaged.

If a leg resists or feels stuck, do not force it. Check for dirt or debris around the hinge and wipe it clean with a dry cloth. Hinges can seize if moisture or dust builds up, especially if the rebounder has been stored in a damp place.

What to do if a spring collar is stuck

Spring collars can become difficult to turn if they have been sitting for a long time or if moisture has caused light corrosion. If you cannot turn a collar by hand, try wrapping a dry cloth around it for better grip and try again. The cloth gives you more friction and makes it easier to apply steady pressure.

If the collar still will not budge, apply a small amount of penetrating oil like WD-40 around the base of the collar where it meets the shaft. Wait five to ten minutes for the oil to soak in, then try turning it again. Wipe away any excess oil with a clean cloth before storing the rebounder.

Do not use a wrench or pliers on the collar, as this can strip the metal or bend the shaft. Hand pressure with a cloth is the safest approach.

Storage tips after closing

Once the rebounder is fully closed, store it in a dry location away from direct sunlight. Moisture is the main enemy of the springs — rust will form on the metal if the rebounder sits in a damp garage or basement for months. If you live in a humid climate, consider placing a small desiccant packet or container of baking soda near the rebounder to absorb moisture.

Keep the closed rebounder away from heat sources like radiators or heating vents, as extreme temperature changes can weaken the springs over time. A climate-controlled closet or storage room is ideal.

Opening the rebounder again

To reopen the rebounder, reverse the closing process. Unfold the legs first by pulling them outward until they lock into place. Then lift the mat up gently and begin twisting each spring collar clockwise to reattach the springs to the frame. Turn each collar until it is snug — you should feel resistance, but do not over-tighten, as this can strip the threads.

Once all springs are reattached, the mat should be taut and the rebounder ready to use. If the mat feels loose or uneven, check that every spring is equally tight. Uneven tension can cause the mat to wear unevenly and make the rebounder less stable.

Common problems and solutions

If the mat does not fold flat even after all springs are released, one spring may still be partially attached. Go around the rebounder again and check each collar to make sure it has been turned all the way counterclockwise. Sometimes a collar will feel loose but still have a thread or two engaged.

If a leg will not fold inward, the hinge may be bent or the frame may be slightly warped. Try folding the other legs first to see if they move smoothly. If only one leg is stuck, the hinge itself may need replacement. Contact Bcan customer support with the model number and a photo of the stuck hinge.

If you notice rust forming on the springs after storage, wipe the affected area with a cloth and a small amount of oil. Light surface rust will not affect performance, but heavy rust can weaken the springs and should be treated before the rebounder is used again.

Frequently Asked Questions

How long does it take to close a Bcan Rebounder Meta Springs?

Closing usually takes five to ten minutes the first time you do it. Once you are familiar with the process, you can close it in three to five minutes. The time depends on how tight the spring collars are and whether any are stuck.

Do I have to close the rebounder, or can I leave it open?

You do not have to close it, but closing saves space and protects the springs from dust and moisture. If you use the rebounder daily, leaving it open is fine. If you store it for weeks or months, closing it is better for the springs.

What if I lose the spring collars?

Replacement spring collars are available from Bcan through their website or Amazon. You will need the model number of your rebounder to order the correct size. Collars are inexpensive and ship quickly.

Can I use a power tool to close the springs faster?

No. A power drill or impact driver can strip the threads or bend the shaft. Always turn the collars by hand to avoid damaging the rebounder.

Is it normal for the springs to make noise when I close them?

A slight creaking or clicking sound is normal as the springs release tension. If you hear a loud crack or snap, stop immediately and inspect the spring for damage. A broken spring should be replaced before the rebounder is used again.